Crafts & Hobbies Information


The Making of a Slipcover: A Lost Art


Today in this world of fast everything, most of us just don't have the time (nor patience) to do an all consuming job of making a slipcover. We go buy them and not always are they what we want. They are generic in most cases and just don't work on the furniture right or look professional. If you can find the time and feel creative, you can produce a masterpiece for an old (or new) piece of furniture that needs a change to correspond with a new room update. The slipcover will produce a sense of confirmation and beauty for "you", the person doing the work. A job well done is always good for growing self- confidence and character!

I owned a very busy tailor shop and I was use to "custom fitting" my clients and worked the slipcovers the same way. When one was finished, it was hard to tell if the piece had been re-upholstered or slip covered. What a great feeling it was to see the finished piece!

So with that said, I have a few techniques for you to use that will make this lost art of slipcover making a bit easier.

Start with a simple furniture piece. A good example would be an ottoman, simple dining chair or a toaster! Look at the piece, see where the natural lines are? That is where the seams will be for the slipcover. Scratch out a picture of your furniture piece, this will help as you take measurements for pieces. Measure width and length, add an extra 1¼" to width and length for seams. Write each piece size down on drawing to reference from. Make sure you have your closure type figured out. You will need to add extra material for overlapping if using velcro or ties and zippers. Where will your closures be? Do you even need one on this slip cover? All of this needs to be calculated into original diagram of furniture piece. We will tailor fit these pieces to the furniture INSIDE OUT. You will end up with all your slipcover pieces being odd sized squares or rectangles, etc. This is easier for quick marking and cutting instead of attempting to cut the exact shape of each piece. There will be some extra material in certain areas (which you will cut away) but it gives you room for making a few mistakes! Remember, the art of slip covers and upholstery is very forgiving!

If you are using denim or heavy cotton or anything that does not have to be dry-cleaned for your slipcover, I suggest you preshrink the material. You can wash and dry it later many times without shrinkage (a great option if you have small children and newer furniture). Choose a solid color. Sheets or curtains (even older ones found at Goodwill if you're on a budget) can work for making slipcovers and you may find them on sale to make the cost less. Cording can be covered and added into prominent seams of the slipcover if you want to add some detail. Most of your material to cover cording with will come from the leftover inches at the sides going along the length. They will be long pieces sewn together on a mitered seam. Cording material width is 1 ¼". Cutting everything with pinking scissors will eliminate (to a certain degree) having to serge or finish the edge of raveling fabric.

You will "railroad" your slipcover measurements by marking them (and eventually cutting), going length wise on fabric and then side by side across the width of fabric. If you have an exceptionally wide piece you will "railroad" it going length of material instead of across, thus avoiding seams. Visualize how the sizes will lay out on the fabric, using drawings here will be very helpful. Example: If you use 60" width material, you will get at least 3 dining chair slipcover backs across, if they are 16" - 18" wide. They could run 36" - 48" in length down the material. Then you will need to figure the inside back, seat, and sides or skirting (remember, if you are doing 2 or more of same, times each piece by the number you are doing). Depending on how much turn up you want for the hem will depend on how much extra you add on side or skirting measurement. Figure out how much material you will need by calculating the length of longest slipcover pieces, adding them together and divide by 36" for yardage. Make sure to utilize the most from your fabric. There are cheat sheets at some material stores that give basic yardage for upholstering & slip covering furniture , see if you can find one, their priceless!

Once you have all your measurements for your slip cover pieces, start with the largest sizes and mark everything out on your fabric, WRONG SIDE. You will need a yardstick or longer, measuring tool. A large square is good to have also. (Any hardware store should carry the tools) Label all pieces; i.e. back back, front back, seat, sides or skirting, etc. Cut your pieces.

Holding your slipcover pieces up to the furniture piece INSIDE OUT, pin the seams together about every 2 inches lengthwise along the seam. Make sure to center your pieces over furniture so you have equal seam allowance on sides, edges, etc. Back-back to front-back, pin. Seat to front-back, pin and so on. Sew these pieces together. Once you start sewing, your seams will only be about 3/8" instead of the full 5/8". This gives the slipcover a tiny bit of room to move when finished. I recommend getting some T-pins to use when you are making slipcovers for larger upholstered pieces, you can stick them into the furniture and they will hold the slipcover fabric in place when fitting the pieces together.

Normally, I will pin fit the whole slipcover together inside out on the furniture piece, then go sew, removing pins along the way. This is similar to a puzzle, make sure to sew all seams that dead end into other seams first. Once you have it sewn together, turn it right side out and fit it. Check for areas that may be a bit off and correct. From experience I can tell you it is usually pretty good if you can sew a straight seam. You can put some masking tape on your sewing machine face plate and mark 3/8" over from the needle to help with this. Complete all finishing touches, stand back and take a picture!

This is a wonderful way to grow patience, skill and redecorate for less. There is time involved, but you will have a great sense of accomplishing a lost art! Have fun!

There is more to this than what I have here, but you should be able to get a pretty good idea of what to do and how. There are some very good books you can get from your public library and material/craft stores to help you and I would be happy to help, if you mail me at the address below.

About the Author:
Robin Hall has been a successful Tailor by trade in the Midwest with over 30 years in business. She has sewn everything from leather, to clothes and alterations including home décor items. She has just started an online home décor store where you will find a little bit of everything including great tips on decorating and home improvement. Please stop by and see us/her at http://www.coollampsnstuff.com or send email with questions to sales@coollampsnstuff.com


MORE RESOURCES:
This RSS feed URL is deprecated, please update. New URLs can be found in the footers at https://news.google.com/news


Terrace Art Zone -- Design & Print a Terrace Bandana
Madison.com
This week's Project: Design and Print a Terrace Bandana Join us for a night of FREE art making & crafting. All supplies are included. Tonight: Design your own bandana by using block printing. Six weeks of unique art projects on the Terrace Upcoming ...



Chain Maille Earrings
Madison.com
Try your hand at chain maille and make a bracelet using the European 4-in-1 technique. Learn to make your own jump rings and clasps, too! No jewelry making experience required, those with previous experience welcome. Course fee includes most supplies ...



Scrapbooking -- Building Memory Pages
Madison.com
Turn your memories into scrapbook page works of art. Use a variety of techniques to create designs that capture the essence of you best stories. We will use the Union Terrace as a theme to practice creating a memory page and learn more about tackling ...



One-on-One Computer Assistance
Madison.com
Need help with basic computer or Internet skills? Looking for assistance downloading library eBooks and audiobooks? We offer free one-on-one sessions Monday and Saturday mornings, and Thursday afternoons! Call 246-4547 to make an appointment.



Duck Tape Mania!
Madison.com
Colored duck tape, creativity, and loads of fun! Bring your family and friends, and make wearable art - wallets, sandals, neckties, purses and more. Instructions and tape provided. All ages welcome, children under 8 must have an adult helper ...



Cool Comets!
Madison.com
Comets are often called "dirty snowballs"! Join UW Space Place and find out where comets are in the solar system, what materials are in a comet, and the difference between comets and meteors. During the workshop, we will make the nucleus of a comet out ...



Midwest Woodlanders Gathering
Madison.com
Whether you're a beginner or an experienced craftsperson, you are in for an incredibly fun and creative time with over 40 nature-based workshops to choose from and more than 20 talented instructors to work with. Create rustic furniture, garden ...



Teen Filmmaking Camp
Madison.com
In this 3-day film making camp, teens will work with a professional filmmaker to produce a short film using the library's digital Media Lab. Attendees will learn what goes into the 'lights, camera and action!' of making a film - from camera work to ...



Stop Motion Animation Workshops
Madison.com
Drop in to play with Madison Public Library's stop-motion and hand-drawn animation stations! Using markers, whiteboards and props, each participant will create their own short stop motion film during these hands-on workshops. All supplies and equipment ...



Drop In -- Mimosas & Market Bags (July Edition)
Madison.com
Farmer's Market season is in full swing! Escape the humidity and join us before or after your Capitol Square loop to enjoy a #drinkandDIY. Sip a mimosa while decorating a large canvas tote bag. Check out our inspiration photos and then embellish your ...


Google News

home | site map
© 2007